What was the original price of the hardinge hlv-h lathe

#WHAT WAS THE ORIGINAL PRICE OF THE HARDINGE HLV H LATHE UPDATE#

You may not use or access any and all PIS services if you do not agree to the Terms stated herein.ДЎ.В All machinery, equipment, merchandise and other items (the 'Goods') are sold on an 'AS IS/WHERE IS' basis with no warranties or representations whatsoever either expressed or implied. By using or accessing any and all PIS services and or Websites you agree you have read and understand the Terms stated herein and are bound to these Terms. The Terms apply to all Transactions, including without limitation, public auctions conducted by PIS and direct purchases by Buyer of any item either before, after or independent of any public auction. Nor have it.Set forth below are the Terms and Conditions (the 'Terms') that shall apply to any purchase by any party (a 'Buyer') either directly from Perfection Industrial Sales (PIS) or in a transaction (a 'Transaction') in which PIS serves as broker, agent, liquidator or auctioneer for any third party owner. and all at 'Dee Cee' torque, roughly 7.5 HP AC equivalent. Roughly 4+ to 6+ HP, given they over-Volted ALL of the nominal 230 VDC motors to around 260 VDC. lest it embarrass you! It ain't just a South Bend 9 or 10 built with real 'Iron' and a blank cheque to purchase. fast, and at low unit-labour and machine-time cost.Д«ut DO keep that mass in mind when you prepare to MOVE it. making multiple gadzillions of small parts. Hardinge has plenty of power to do what they were best at. puts them surprisingly close to the weight of a Monarch 10EE (roughly 2800 to 3300 Avoir, depending on whether heavy MG or lighter Vacuum tubes.) with a Helluva lot more chip-ripping power and stiffness up-top at the tool-tip. The all-up mass of small lathe, big cabinet, lots of 'stuff' in it, and built to stay stiff and last a long hard working life. so far.ДЄ Hardinge base 'cabinet' is NOT the lightweight office-desk category animal it might at first resemble. Would be a good first project on a new lathe to make a part for that lathe.Nothing to add but one thing no one has mentioned. I'm am more worried about something being broken and that's why the level isn't there. But by then, you'll have a better idea of what needs done and what issues it has. With time, you may well get to the point where you have the tools, skills and desire to rebuild it to new condition. Haven't used my Myford in the 10 years since I finished rebuilding my HLV, although the Myford was vital in making parts for the rebuild (mine was a basket case, this one looks far better). If the feeds work, the collet closer works and the bearings aren't noisy, it'll work fine as a first lathe and may well spoil you for any other lathe. The amount of work needed can only be determined by close inspection.

Could be a good sign, that the apron has had some maintenance/rebuild in the past.ДЄny HLV is going to need work unless it has been mothballed for the last 40 years. Possibly both mechanisms and the power feed motor have been taken from different machines.

The cross slide power feed clutch cam mechanism has been replaced with one from an HLV-H, the carriage feed one on the left is the original HLV type. Could be just missing or there could be issues with the mechanism. The top slide screw threading quick retract lever is missing.

#WHAT WAS THE ORIGINAL PRICE OF THE HARDINGE HLV H LATHE UPDATE#

I'd appreciate any input and will update the post once I get more pictures. I am hoping that this lathe will stick with me for a while. I have restored machines in the past and am not afraid to dig into them a bit to make sure they keep running for a long time. It is in need of a paint job which I am fine with. I don't have to hunt any parts down or buy a clapped out machine. What I really would like to know is what I should look for on the lathe as far as wear and what should be included. It is also a 6-7 hour drive for me so I can't just go look at it real quick. They said it comes with chucks and collets but I am still waiting on pictures of everything it comes with.

I came across what seems to be a good deal on a HLV-H and it is an older model so it's not going to break the bank for me. This would be my first lathe and I prefer the buy once, cry once mentality on quality tools. My friend is a huge Hardinge fan and has talked about them a lot in the past so I started looking into getting a HLV-H. So I have been looking at getting my first lathe for some time and initially was intrigued by the monarch 10ee but never really considered them since they are so heavy.

What was the original price of the hardinge hlv-h lathe